GSM Fixed Wireless Terminal With LCD Display FWT 8818L

GSM Fixed Wireless Terminal With LCD Display FWT 8818L

GSM FWT-8818 is a GSM to Analog Converter, the device can produce a FXS line to allow a regular phone to be connected and used just like a local landline(PSTN) except your calls will go out the GSM network. This device can both receive and make calls.

Products Detail

Specification of this GSM Fixed Wireless Terminal GSM FWT 8818 With LCD Display
 

GSM FWT-8818 is a GSM to Analog Converter, the device can produce a FXS line to allow a regular phone to be connected and used just like a local landline(PSTN) except your calls will go out the GSM network. This gsm fwt fixed wireless terminal device can both receive and make calls.

The wireless terminal With LCD Display main application is: Connecting the RJ-11 FXS line to connect Ordinary telephone set for voice call, to connect PBX for call extensions, to connect billing systems for public phone use, to connect VoIP gateway to realize VoIP call termination,High Quality gsm fwt fixed Wireless terminal to connect alarm panels for security purpose, etc.

Especially, GSM FWT-8818 provide SMS management for SIM credit balance inquiry, Low battery alarm, SMS remote control for alarm panel, and SMS remote control for relay etc. so gsm fixed wireless terminal is a better choice for alarm security application.

Available:

l GSM 900/1800Mhz dual band, employing SIM500W,Sim300W module to make;

l GSM 850/900/1800/1900Mhz Quad band ,employing Quectel M35 to make.
 
Features: 

1) LCD display GSM FWT,Simple to install and easy to maintain

2) Steady module(SIM500W,300W,Quectel M35) and reliable design ensures good performance

3) Provides optimized circuit directly connecting the exchange device for extensions

4) Compatible to most telephones, PBX (for call extensions), Alarm panels (for security) and VoIP gateways (for call terminations)

5) Strong signals with high gain antenna

6) Attractive plastic casing

7) SIM card supported (1.8V, 3V)

8) Caller ID display

9) Provides reversal polarity signal for metering

10) No noise and clear voice

11) Suitable for wide voltage range and low power consumption

12) Suitable for all kinds of weather and environmen

13) RJ-11 ports

14) Locking PIN / network (optional)   

15) Back up Li-ion battery( Optional) 7.2V 1300mAh.standby 24hrs,talking time: 2.5hrs.

 
Parameters of this GSM Fixed Wireless Terminal GSM FWT 8818 With LCD Display
 
Appearance and Structure
 

Item

GSM FWT-8818

Remark

Appearance

 

White

Material

ABS (Acrylonitrile Butadiene Styrene)

 

Dimension

155mm×112mm×30mm

Excluding antenna

Weight

350g

Weight of Main unit

Power Switch

Rocker switch

 

Power Socket

12V DC input

 

Phone interface

RJ11

1RJ-11

Antenna interface

SMA-female

 

Interface View

 

 

 
Technical Specifications
 

Air interface standard: GSM850/1900Mhz,900/1,800Mhz phase 2+ full band
Frequency ranges:
 A) GSM 850                                        GSM 1900:
 I) Transmission: 869.2 ~ 893.8MHz      I) Transmission: 1, 930 ~ 1, 990MHz
 Ii) Reception: 824.2 ~ 848.2MHz          Ii) Reception: 1, 850 ~ 1, 910MHz
 B) GSM 900:                                      GSM 1800:
 I) Transmission: 890 ~ 915MHz           I) Transmission: 1, 710 ~ 1, 785MHz             
 Ii) Reception: 935 ~ 960MHz               Ii) Reception: 1, 805 ~ 1, 880MHz
Phone interface: supply RJ-11 Phone Interface
Hanging voltage: 45V
Picking off voltage: 30mA / 41mA
Dialing tone Frequency: 450Hz
Antenna interface: Antenna amplifying>2.5db
Sensitivity:<-104DBM
Transmitting power<3W

Color: White

AC-Adapter interface: Input: AC 110~240VAC  50~60Hz
                    Output: 12DC 1A.

AC-Adapter type: EU, US, AU, British can be optional

Operation Circumstance: 

Operation temperature: -10c~60C
Storage temperature:-20C~70C
Operation humidity:45%-95%
Atmosphere pressure:86-106Kpa
Environment noise: <60DB
Transmitting Power:2W
Sensitivity: <-104dbm
Antenna Amplifying: >2.5db
Dialing frequency: 450Hz
Hanging voltage: 45V
Picking current: 30mA/41mA

Packing List

Name

Quantity

Remark

GSM FWT-8818

1pcs

Dual band or Quadband

Ac- adapter

1pcs

AC-110-240V, DC12V/1A

Antenna

1pcs

Magnetic Antenna with 3m cable

User's Manual

1pcs

English

G.W: 0.65kg per unit. 20pcs/CTN, 14kg /CTN,CTN Size: 55cmX34.5cmX26.5cm
 
Installation And Connection

The Condition for Installation

The terminal asks for 110- 220V AV power supply. It must be installed in the area where the GSM network can cover. The strength of the signal can affect the quality of voice.

1. Insert SIM card into the SIM card holder at the back of the terminal.

2. Install antenna. In order to ensure the quality of voice, antenna must be put beyond 1.5 from the telephone and terminal.

3. On end of the telephone line connects to the “Phone” port of the terminal, the other end connects to telephone.

4. “Power” port connects to power adapter that is connected to 110-220V AC power supply.

1) The Installation for Connecting to Ordinary Telephone

The Sketch for connecting ordinary Telephone

Draw your attention: Because there are many types of ordinary telephone and their electric parameters are different. In order to avoid mutual disturbance between telephone and terminal and affect voice quality. The distance between telephone and terminal is 1.5m at least.

 

2) The installation for connecting to billing device for metering

If the users demand to register cost during calls, billing device can be connected between terminal and ordinary telephone. Billing device register cost according to the anti-polarity signal that is provided by terminal.

 

The sketch for connecting to Billing device or Computer charging system

The installation for connecting to PBX for call extentions

If users want to connect small PBX to this terminal, connect terminal's “Phone port” to the PBX.

 

The sketch for connecting to PBX device.

The installation for connecting VoIP gateway for Call Termination

Suppose a VoIP call originates from US, which was transferred from US Server to China Server on VoIP, finally the call will be terminated from internet to GSM network and to be sent out to the destination answer side.

 

The sketch for connecting to VoIP gateway

The installation for connecting to alarm system for Security

The GSM FWT can substitute the PSTN for connecting to alarm system for security purpose when PSTN failure or not available.

 

The sketch for connecting to alarm system

Function Setting

Before you do the following function settings, Lift handset or press hands free key of telephone set, then you can press the buttons according to the following instructions to finish setting, you will hear 2 beeps when you finish, this testify setting successfully.

 

1) Restore to factory default setting

*#99#99# restore to factory default setting.

 

2) Adjust dial interval

*#01#30# , 01--command,30--time,Max 9.9 seconds,Min 0.5 seconds, default setting is 3 seconds.

*If you use GSM FWT-8818 for connecting to VoIP gateway, you can set dial interval as 0.5 second, it can make PDD<5 sec (Method: *#01#05#);

*If you use GSM FWT-8818 for connecting telephone, PBX, billing device, you can set dial interval as 3 seconds or 5 seconds as you like (Method: *#01#30#, set the dial interval as 3 seconds).

 

3) Adjust Earphone Volume

*#02#15#  02--command,15--volume,Max 16,Min 1, default setting is 15.

 

4) Adjust Mic. Volume (sensitivity)

*#03#10#  03--command,10--amount,Max 16,Min 1, default setting is 10.

 

5) Setting local area code

*#04#*0755#   10--command,*0755—area code,Max 5 numbers, use "*" instead if area code is less than 5 digits.

 

6) Setting IP numbers

*#05#17911#  05--command,17911—IP numbers,Max 5 numbers, use "*" instead if IP number is less than 5 digit.

 

7)Hide Caller ID (been sent out)Setting

*#13#01# 13--command,01--value,Max-02,Min-00 Default setting is 00

00-- presentation indicator is used according to the subscription of the CLIR service

01 – CLIR allowed

02 – CLIR prohibited

Notice: This Setting need GSM carrier support.

 

8) Bar incoming call Setting

*#14#00#  14--command,00--value,00--no barring, 01--set barring   default setting --00

 

9)FSK setting (optional) (should confirm before order)

*#17#00# setting caller ID

17-order, 00-value, 00-DTMF, 01-FSK, default setting is 00

This setting need terminal has FSK Chip set support

 

10) Billing Mode setting

 *#15#00#

15--command, 00-value, 01-reversal polarity, 02-12 KHz, 03-16 KHz, default setting-- 01

 

11)IMEI change Setting ( for Quad Band M35 Module only)

1. Write IMEI to RAM

*#18#IMEI no.#, 18--command, IMEI No. --15-digit IMEI no.

2. Check IMEI, if it is right, and then write it to module.

*#19#IMEI no.#, 19--command, IMEI No. --15-digits IMEI No.

Notice: Step 1 and Step 2, IMEI no. must be same.

 

12) Pin Lock &Network Lock Setting (optional)(Should confirm before order)

2)PIN Lock

1, Set to open PIN code check and automatic PIN lock function

*#07#*1234#  07-command, 1234- the current SIM card PIN code

If set sucessfully, the device will open PIN code check, and automatically change the current SIM Card into "PIN on" from "PIN off"

 

2, Set to close PIN code check and auomatic PIN lock function

*#08#*1234#  08-command, 1234- the current SIM card PIN code

If set sucessfully, the device will close PIN code check and automatic PIN lock function.

 

3, Set to change PIN code,open automatic PIN lock function

*#09#1234*56785678# 09-command, 1234- the current sim card PIN code, 5678-new PIN code. (5678 can be any other 4 digits number, suppose you can use 2009).

If set successfully, the device will change the current sim card PIN code as you want.5678, or the any other 4 digit PIN codes, and open automatic PIN lock function.

2)Network Lock

1,Set to open Network lock function

*#10#01234# 10-command, 01234-password

2,Set to close Network lock function

*#11#01234# 11-command,01234-password

3,Set the Network codes

*#12#1*46003*46003# 12-command,1--No. Of IMSI, 46003--the IMSI code for China Telecom

*#12#2*46000*46000# 12-command, 2--No. Of IMSI, 46000--the IMSI code for China Mobile

SMS management

See SMS management file

Making Calls and Answer Incoming Calls

Making Calls

1. Lift the handset or press “hand-free” key, you will hear dialing tone, then you can dial the telephone numbers you want to call.

2. Dialing: dialing the telephone numbers you want to call

3. On completion of dialed digits, you can press “#” to transmit the called telephone numbers. If you don't dial any key for continual 3 seconds during the dialing, terminal transmits called telephone numbers automatically.

4. During calls, if the telephone numbers is not free ones, the terminal sends out anti-polarity signal.

5. If the calling party or called party hangs up, the terminal stops sending out anti-polarity signal.

Answering Incoming Calls

When some calls are coming in, if the connected telephone has the function of displaying incoming calls, the telephone rings and displays the incoming telephone numbers. Now users can lift the handset or press “hand-free” to answer it.

Warranty Card

Please fill in the blanks carefully, and keep it properly as the voucher for warranty.

Type of Equipment

 

GSM FWT-8818

User's name

 

Contact with:

 

Contact Tel.no.

 

Address

 

Date of Ex-works

 

Date of Maintenance

Damage

Management

Maintainer

Sales Agent

(Stamp)

 

Purchasing Date

 

 
Please fill in the blanks carefully, and keep it properly as the voucher for warranty.
 
Pictures of this GSM Fixed Wireless Terminal GSM FWT 8818 With LCD Display
 

 

 

 

Looking forward to your inquiry for this GSM Fixed Wireless Terminal GSM FWT 8818 With LCD Display

Tags

Leave your messages:

Send Inquiry Now

Related Products

Send Inquiry Now